|
|
|
BRM OFFROAD |
||
|
|
GRAPHIC SHOP - INFO | |
|
Thanks for visiting the BRM OFFROAD Graphic Shop. Looking for some awesome custom graphics and stickers? We specialize in custom graphics (printed or die cut) and logo designs. Our stickers are BRM OFFROAD custom designs, not clip art. ALL our Quad (ATV), Dirtbike, Motorcycle, UTV, Sand Rail, Truck, Buggy, Jeep, Snowmobile, and Jet Ski stickers were drawn in house by our top of the line design team and they have all been registered with the U.S. Copyright Office. They are the sole property of BRM OFFROAD and we do not sell our art files. Visit our Legal page for more info. Give us a call if you can't find what you're looking for, we will even create your sticker from your very own photo. Custom sizes are also available. We have a large variety of stickers to choose from to get you set up: If you don't see the one your looking for, let us know. We will also provide you with great looking, pre-printed numbers for your quad, dirt bike, utv, truck, or buggy, graphic kits, jersey lettering, and chest protector I.D. plates.
Our services also include vehicle graphics for cars, trucks, trailers, boats, and more. We can create a fresh logo for you or recreate your current one. We also make magnetic signs, banners, and signs for your race team, business, schools, or your kids' events. All graphics are done in-house and your satisfaction is our #1 goal. We have safe and secure on line shopping for all your shopping needs. Below you will find installation instructions for large or multi-colored stickers and graphics. Paypal information, along with shipping information and delivery transit times.
|
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| PAYPAL SHOPPING CART INFO | ||||||||||
|
|
|
|
|
|
|
|||||
|
|
|
|
|
|
|
|||||
|
INSTALLATION INSTRUCTIONS FOR STICKERS & MULTI-COLORED GRAPHICS (read & print to have handy during install) |
|
|
|||||
 |
STEP #1 |
 |
STEP #2 |
 |
STEP #3 |
| Thoroughly clean surface and remove any grease or wax. Although it's not required, we recommend using rubbing alcohol as a final wipe down before you get started. Align graphics where you would like them and place masking tape across entire edge of your graphic to your application surface, holding the graphic in place. | If there are rivets to work around, take a pen and draw a circle around the rivet head and then carefully cut thru the top layer of tape, the graphic, and the backing paper with a pocket knife or razor blade. | Pull the backing paper away from the graphic and transfer tape, being extra careful to keep the graphic from folding in on itself or sticking to the surface before you're ready. | |||
 |
STEP #4 |
 |
STEP #5 |
 |
STEP #6 |
| Now that you have the backing paper removed, lightly mist the "sticky" side of the graphic and transfer tape with tap water and a water bottle. Do not spray if applying to glass. The water helps to re-lift the graphic if you start getting an air-bubble. | Start laying the graphic down on your surface while your partner uses a squeegee or drivers license to apply the graphic, with light to medium pressure. Start in the center along the top, working your way downward, laying the graphic closer to the surface as you go. Then move back to the top and work your way down and out towards the sides. Take your time and don't rush yourself. | Once you have the graphic applied to the surface, go back over the graphic with your squeegee pressing more firmly against it. Be careful around the rivets and take your time. You're just about done. If it's cold outside, use your hair dryer to warm the graphic before going on to the next step. Just warm it, don't get it too hot as this will stretch the vinyl and may make it out of proportion. | |||
 |
STEP #7 |
 |
STEP #8 |
 |
STEP #9 |
| This is the final step for a 1-Color Graphic or Sticker. Remove the masking tape that you applied in step #1. Start in one of the top corners and start peeling the transfer tape off. Try to peel it at a 45 degree angle. If the graphic should lift (not release from the transfer tape), simply press it back down with your fingers or squeegee. The colder it is outside, the longer it will take. Use your hair dryer again if you need to. You can always re-stick the transfer tape and press firmly with your squeegee again. | For Multi-Colored Graphics cut and remove the backing paper from the registration mark, making sure the registration mark is stuck to the transfer tape. Now you will want to line up this registration mark with the registration mark from the 1st color you laid down. | Repeat Steps 1-7. Remember to cut around any rivets before you start lifting the graphic and transfer tape from the backing paper. Take your time and use your hair dryer if needed. | |||
 |
STEP #10 |
 |
STEP #11 |
 |
STEP #12 |
| Remove any registration marks that you may have had. If it's cold out, break out that hair dryer again and simply use your finger nails to remove them. | Stand back and admire your work! | Take a picture and email it to us and we'll add it to our site. Thanks for your business!!! | |||
|
*
Order By Phone or Shop On-Line
or
or
,
Monday thru Friday
thru
